D840WP
32mm, Waterproof, Cored, Wide Voltage, High Speed Actuator (7.4V)
Our D840WP industrial actuator offers a wide voltage range, as well as IP67-certified water & dust-proof protection, making it suitable for many industrial applications. Featuring a machined aluminum-composite case to dissipate heat, two ball bearings and four steel gears, a digital amp with MOSFET drive, and both PWM & PWM/TTL control protocols, this powerhouse delivers nearly 420 oz-inches of torque and high-speed operation. Program parameters such as End Point Adjustments, Direction, Speed and Fail-Safe position to optimize the installation and performance when your industrial applications demand that extra level of performance and capability.
Part #: 36840S
$134.99
Maximum of 20 units per part # are available for purchase on our website.
Contact Sales directly to discuss purchases over 20 units:
Actuator Sales
sales@hiteccs.com
| Performance Specifications | |
|---|---|
| Command Protocol |
PWM PWM / TTL |
| Operating Voltage (V) |
Min: 4.80
Max: 7.40 |
| Weight (g) | Min: 227.00 |
| Stall Torque (kgf•cm / oz•in) |
Min: 19.0 / 265.31
Max: 30.0 / 418.91 |
| No Load Speed (sec/60°) |
Min: 0.17
Max: 0.11 |
| Running Current (mA) |
Min: 1100
Max: 1600 |
| Stall Current (mA) |
Min: 5000
Max: 9000 |
| Circuit |
Digital |
| Rotation |
Standard |
| Operating Voltage (V) |
Min: 4.80
Max: 7.40 |
| Torque Range |
Min (KG/CM): 30.00
Max (N/CM): 0.00 |
| Max Speed (SEC/60) | 0.11 |
| Physical Specifications | |
|---|---|
| Case Size (mm) | 32.00 |
| Dimensions (mm) | 66.0 x 32.0 x 62.0 |
| Weight (g) | 227.00 |
| Motor Type | 5 Pole Cored Carbon Brush |
| Potentiometer |
Conventional |
| Gear Material | 1 Metal-Karbonite & 4 Steel |
| Horn Gear Spline | 13 Segment / Ø7.7 |
| Case Material | Engineering Plastic / Aluminum |
| IP Rating |
IP67 |
Contact Sales directly for accessories and/or replacement parts:
• Case Set
• Gear Set
• Horn Set
Actuator Sales
sales@hiteccs.com
Standard Programming Functions
- End Point Adjustments
- Direction
- Fail Safe
- Dead Band
- Speed (Slower)
- Soft Start Rate
- Overload Protection
- Data Save / Load
- Program Reset
IMPORTANT INFORMATION > DPC-20 PROGRAMMER
- Hardware Type: PC USB-C to 3-pin (PWM/TTL) and 4-pin (RS485/CAN) interface.
- Capable of configuring and testing HITEC digital servo actuators.
- Compatible with various control methods (PWM, RS485, CAN), offering a seamless transition from legacy DPC-11, DPC-485, and DPC-CAN units.
- Different servo actuator series require dedicated UI programs due to variations in communication protocols.
- Ensure you connect the appropriate power supply to the DPC-20 for the connected servo actuator.
- For servo actuators (5/7 Series, 9 Series, D/MD Series), connect to the 3-pin port on the DPC-20, and connect the power supply to the BAT- and BAT+ pins on the 4-pin port, paying careful attention to polarity.
- DPC-20 Wiring Diagrams are located on the DPC-20 UI HUB DOCUMENTATION.
Additional downloads can be found on our ACTUATOR RESOURCES page under our Support tab.
Contact Sales directly if you are unable to locate a specific resource download:
Actuator Sales
sales@hiteccs.com
